FREE SHIPPING ON ORDERS $45 OR MORE (BEFORE TAX) U.S. ORDERS ONLY.

CrazyBee F4 Pro V2 1-3S Brushless FC (NO RX)

GnarlyFPV

Regular price $37.00 Sale

CrazyBee F4 Pro V2 1-3S Brushless Whoop Board

Included:

  • 1 x CrazybeeF4 PRO flight controller
  • 3 x power cables
  • 1 set shock absorbing rubber and screws

NOTE:

  • DO NOT RUN THESE BOARDS WITH THE HYPER LITE TOOTHPICK MOTORS WITH THE HIGH KV ON ANYTHING OVER 1S. 
  • We have begun testing each and every FC we carry before selling them. That includes: Power by USB, Power by 1s, 2s and 3s (Without soldering on a connector). Plugging in motors and testing each motor through Betaflight pass through. We want to insure that we are sending a working FC board to all of our customers. The GnarlyFPV QC stamp! 

 

Specs:

The biggest differences between Crazybee F4 PRO V1.0 and V2.0 are:

V2.0 could handle 1-3s Lipo/LiHV

V1.0 could handle only 1-2s Lipo/LiHV

V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”

Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-3S battery input (DC 3.5-13V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
ESC MCU Upgraded to EFM8BB21
Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS-2A Compatible)
DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver)
No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc.
Built-in Betaflight OSD (SPI Control)
Built-in Current meter sensor Max up to 28A
Current meter scale set to 1175
Built-in 5V 1A Buck / Boost with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Multi Serial port support
Fully compatible with almost Brushless whoop drone
Weight:4.3g
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.Hex
Default protocol: DSHOT600
Receiver support No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc.

Firmware target:

Frsky version  betaflight_4.0.0_CRAZYBEEF4FR.hex

Flysky version betaflight_4.0.0_CRAZYBEEF4FS.hex

DSM2/DSMX version betaflight_4.0.0_CRAZYBEEF4DX.hex

No RX version betaflight_4.0.0_CRAZYBEEF4DX.hex

http://www.happymodel.cn/index.php/2019/01/05/crazybee-f4-pro-series-flight-controller-firmware/

 

NOTE:

  • DO NOT RUN THESE BOARDS WITH THE HYPER LITE TOOTHPICK MOTORS WITH THE HIGH KV ON ANYTHING OVER 1S. 
  • We have begun testing each and every FC we carry before selling them. That includes: Power by USB, Power by 1s, 2s and 3s (Without soldering on a connector). Plugging in motors and testing each motor through Betaflight pass through. We want to insure that we are sending a working FC board to all of our customers. The GnarlyFPV QC stamp! 

People who bought this product, also bought